Page 1 of 2
Heat shield on 1600
Posted: Mon Dec 20, 2021 1:47 pm
by GarageGuy
20211220_115002(1).jpg
All my pics are too large. I have a 2 inch by 14 inch heat shield with a copper color tube hooked to it. Lines up ok above the exhaust manifold. HELP !!

20210919_165521.jpg
THE LITTLE BARREL WITH A WIRE ON IT ON THE INTAKE MANIFOLD. ANY BODY ?
Re: Heat shield on 1600
Posted: Mon Dec 20, 2021 2:03 pm
by chest rockwell
What's the question?
Re: Heat shield on 1600
Posted: Mon Dec 20, 2021 2:16 pm
by GarageGuy
Had the motor out and can't remember where it bolts on.
It's cut to fit over the exhaust manifold. What am I missing ?
Re: Heat shield on 1600
Posted: Mon Dec 20, 2021 2:58 pm
by RBMann
Re: Heat shield on 1600
Posted: Mon Dec 20, 2021 4:24 pm
by GarageGuy
You saved my life

It's an AC car too. LOTTA extra hoses and connections.
Thanks Fanatic
Re: Heat shield on 1600
Posted: Mon Dec 20, 2021 6:36 pm
by unklpat
AC? Do tell the tale... Pat
Re: Heat shield on 1600
Posted: Tue Dec 21, 2021 12:10 pm
by zippy67roadster
Re: Heat shield on 1600
Posted: Tue Dec 21, 2021 2:37 pm
by unklpat
GarageGuy, since we saved your life, we should be on a first name basis. Also, please submit pics of both sides of your motor, and maybe we can save its' performance life. Pat
Re: Heat shield on 1600
Posted: Tue Dec 28, 2021 11:49 am
by GarageGuy
I'm Mark. 90% sure it's got AC. The pump was not hooked up when we got the car.
Had it purring like a kitten the day it showed up from New Jersey. Next morning, it had a terrible knock. Pulled the motor. Machine shop found a large lock washer stuck to the head in number two cylinder. Got it all fixed. Machined the head flat, and heRE we are.
Re: Heat shield on 1600
Posted: Tue Dec 28, 2021 12:08 pm
by GarageGuy
No AC ? ITS a smog pump ? Tried to load a pic of it.
Motor ran fine without it
Re: Heat shield on 1600
Posted: Mon Jan 03, 2022 11:51 am
by GarageGuy
I reinstalled intake and exhaust manifolds and carbs without wiring up the starter. Had the manifolds off while looking for heatsheild mounts. What a DAMN NIGHTMARE.
I hate working in this turd
Re: Heat shield on 1600
Posted: Mon Jan 03, 2022 11:54 am
by spl310
Consider putting it on stands and removing the tire to gain access to the starter. If the triangular piece is still there, you can drill out the spot welds, remove it, do the work and then reinstall it with rivnuts.
Re: Heat shield on 1600
Posted: Mon Jan 03, 2022 3:07 pm
by Curtis
spl310 wrote: Mon Jan 03, 2022 11:54 am
Consider putting it on stands and removing the tire to gain access to the starter. If the triangular piece is still there, you can drill out the spot welds, remove it, do the work and then reinstall it with rivnuts.
If it is a high windshield car which I'm sure it is with a smog pump, you do not want to screw with the triangle piece. It is a box structure and has bigger opening then the early cars since it is at a steeper angle.
Re: Heat shield on 1600
Posted: Mon Jan 03, 2022 3:12 pm
by Curtis
Re: Heat shield on 1600
Posted: Mon Jan 03, 2022 5:23 pm
by spl310
Looks like that will allow access without any mods.