Datsun Roadster Forum-311s.org

Hi there, is anyone know the dimension of the rear FAIRLADY emblem size? I cant find this emblem anywhere, so i think I might just custom made a metal emblem myself, i have all the tools for this. Really appreciate it if anyone have this information

Thanks

Rallye has them for $169

http://datsunroadster.com/SUB_SECTION_D ... mblems.htm

Here you go.
The whole are for the pin placement

Doggggboy wrote: ↑Wed Jun 17, 2020 10:34 am IMG_20200617_093038.jpgIMG_20200617_093008.jpgHere you go.
The whole are for the pin placement

I dont think its a same emblem, yours is the 1500, mine is 2000

Thanks though

datsun1500 wrote: ↑Wed Jun 17, 2020 5:49 am Rallye has them for $169

http://datsunroadster.com/SUB_SECTION_D ... mblems.htm

Thanks

From Rallye
"The metal version of this emblem #638-13 was original equipment on 63-65 USA Datsun 1500's and was original equipment on 63-70 1500/1600/2000s that stayed in Japan or were exported to certain other countries. It was used on the front fenders of the non-USA 1600 and 2000 and the script emblem #798-09 was used on the rear. "
I bought this car in Canada, but am not sure where it was sold originally.

If you end up making the more modern script and you want to amortize the cost over multiple units, I'd be up for a couple. However, paying over $100.00 for each is out of my range. The older, cursive version looks like it might interfere with the side moulding-at least on my car.

The Block letter 'FAIRLADY' version was used in the US market on 63-65 1500, which had peg holes specific to the 1500 fenders. It was also used in Japan on the later 65-70 1600/2000 wih a different peg configuration (than the 1500)

The Larger Script version 'FAIRLADY' is used on the rear panel (not the fender). It works for 1964-1970 rear panels.

Thanks to all master for all the history write up here, but does really anyone know the dimension of this emblem, I saw some selling over $160-200 for this emblem, me personally think its out of my range. I have a 3d printer, so I can print it out and cast it into metal or anything, it would only set me less then $20.
Anyone can help me out with the dimension is really helpful

I believe the rear emblem should be Datsun_1500. Every stock one I've seen including the one I owned had Fairlady on the fenders and 1500 on the back.

Curtis wrote: ↑Thu Jun 18, 2020 11:52 am I believe the rear emblem should be Datsun_1500. Every stock one I've seen including the one I owned had Fairlady on the fenders and 1500 on the back.

Only on the 1500s. He has a later car and wants the jdm badge.

hlry-2 wrote: ↑Wed Jun 17, 2020 4:20 am Hi there, is anyone know the dimension of the rear FAIRLADY emblem size? I cant find this emblem anywhere, so i think I might just custom made a metal emblem myself, i have all the tools for this. Really appreciate it if anyone have this information

Thanks

I just took a picture of mine and measured it

Height: 40mm at the "F" and 48mm from the "d to y"
Length: 22cm


My goodness this was a tough thread to read!

Alvin wrote: ↑Thu Jun 18, 2020 9:56 pm

hlry-2 wrote: ↑Wed Jun 17, 2020 4:20 am Hi there, is anyone know the dimension of the rear FAIRLADY emblem size? I cant find this emblem anywhere, so i think I might just custom made a metal emblem myself, i have all the tools for this. Really appreciate it if anyone have this information

Thanks

I just took a picture of mine and measured it

Height: 40mm at the "F" and 48mm from the "d to y"
Length: 22cm


My goodness this was a tough thread to read!

You make my day. Thank you so much