Page 50 of 99
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Mon May 28, 2018 12:24 am
by peeeter
spl310 wrote: ↑Sun May 27, 2018 9:46 pm
Post a picture of the loop/tab.
There should be a picture, its the loop on the outside, between the two rain gutters.
pebbles wrote: ↑Sun May 27, 2018 10:35 pm
Wraps around the top frame hinge so your hair doesnt get pinched in the pivot, (60s hair .) .)
There's a pouch on the inside that warps the hinge, this loop is on the outside.
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Mon May 28, 2018 3:25 am
by Lorna c
this in the circle ? never seen one . do u have it on both sides ?
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Mon May 28, 2018 3:28 am
by Lorna c
peeeter wrote: ↑Sun May 27, 2018 9:07 pm
Anyone know what this loop/tab is for on my soft top?
this in the red circle ? odd . but I'm not a long time rider of these yet . but I've never seen one in this spot before . do you have on both sides ?
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Mon May 28, 2018 11:31 am
by C.Costine
That looks something like the top that was on my 67.5 there was a flap that I think that had a couple of snaps to hold it that partially enclosed the frame.
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Mon May 28, 2018 11:48 am
by peeeter
Lorna c wrote: ↑Mon May 28, 2018 3:25 am
this in the circle ? never seen one . do u have it on both sides ?
Yup! That's the piece, and yea, I have it on both sides.
C.Costine wrote: ↑Mon May 28, 2018 11:31 am
That looks something like the top that was on my 67.5 there was a flap that I think that had a couple of snaps to hold it that partially enclosed the frame.
Mine is a 67.5 also, the loop has no snaps, its just a loop that is sewn there.
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Mon May 28, 2018 3:18 pm
by spl310
I've not seen one made quite like that. The picture didn't load for me the first time.
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Mon May 28, 2018 3:44 pm
by Lorna c
peeeter wrote: ↑Mon May 28, 2018 11:48 am
Lorna c wrote: ↑Mon May 28, 2018 3:25 am
this in the circle ? never seen one . do u have it on both sides ?
Yup! That's the piece, and yea, I have it on both sides.
C.Costine wrote: ↑Mon May 28, 2018 11:31 am
That looks something like the top that was on my 67.5 there was a flap that I think that had a couple of snaps to hold it that partially enclosed the frame.
Mine is a 67.5 also, the loop has no snaps, its just a loop that is sewn there.
haha well make something up for it's use is what I do .
note : don't do it in the engine though . not a good idea
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Thu May 31, 2018 3:03 am
by peeeter
I've emailed Steve at acme auto to see what they say, will report back once I find out.
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Thu May 31, 2018 11:10 am
by Linda
Looks like it should be on the inside. I think I would just want to cut it out
Linda
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Thu May 31, 2018 3:11 pm
by mraitch
Installing the engine on Eliza.
Seem to have misplaced some wiring since I cannot see where the temp sender attaches to the rest of the harness.
Any help would be appreciated.
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Thu May 31, 2018 4:06 pm
by greydog
The temp sender wire on our 69 1600 comes out of the main harness on the driver front near the washer pump wires. I think its a yellow wire.
Dan
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Thu May 31, 2018 7:50 pm
by onsight512
What's the fuel tank capacity? Mine is a '69 1600 if it matters.
thanks,
Chris
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Thu May 31, 2018 8:07 pm
by Nissanman
43L or 11US gallon
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Thu May 31, 2018 11:34 pm
by onsight512
Nissanman wrote: ↑Thu May 31, 2018 8:07 pm
43L or 11US gallon
Thanks!
Re: The Quick/Small/(Stupid?) Question Thread-take 2
Posted: Fri Jun 01, 2018 4:28 am
by Lorna c
mraitch wrote: ↑Thu May 31, 2018 3:11 pm
Installing the engine on Eliza.
Seem to have misplaced some wiring since I cannot see where the temp sender attaches to the rest of the harness.
Any help would be appreciated.
is the motor in already ? . I'm still up to learn some more about this motor , if your still tinkering with it, can I watch and learn ?