What did you do TO or FOR your Datsun today?(Roadsters only)
Moderators: notoptoy, S Allen, Solex68
-
- Roadster Newby
- Posts: 18
- Joined: Mon May 01, 2017 8:56 am
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
Done installing my new voltage drop regulator. Then I cleaned the engine bay.
- msampsel
- Roadster Nut-Site Supporter
- Posts: 1812
- Joined: Mon Jul 14, 2014 5:31 pm
- Location: SoAZ
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
Yikes, these bearings with good grease should not rust. Good to see you are giving them attention!Jujuman wrote:See the rust on bearings
IMG_4029.JPGIMG_4028.JPGIMG_4027.JPG
Also some brake fluid crusts
IMG_4008.JPG
Long ago (1974/75 or so) on the return of a 1700 mile journey, I could hear squeaking coming from the rear of my car.
Well the passenger side bearing gave out, and the axel shoved my tire under my wheel well and chewed it up. The car still went straight down the road. Good to give these rear bearing the respect they deserve!
67 1600 (Mods only a mother could love)
78 911 SC Targa (Severe Oversteer but still loved)
78 911 SC Targa (Severe Oversteer but still loved)
- msampsel
- Roadster Nut-Site Supporter
- Posts: 1812
- Joined: Mon Jul 14, 2014 5:31 pm
- Location: SoAZ
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
Well I managed to get all the connections under the car ready to pull.
As we said in my former job, "cleared to fire". Well almost ...
The hardest part so far of all of this effort, was getting the top bolt/nut off my header/exhaust flex tube.
If I could stand up it would have been a lot easier.
Allen bolt will make it so the next owner cannot blame this on me.
Had to wack my half inch wrench with a hammer to get two of the drive shaft nuts started.
As we said in my former job, "cleared to fire". Well almost ...
The hardest part so far of all of this effort, was getting the top bolt/nut off my header/exhaust flex tube.
If I could stand up it would have been a lot easier.
Allen bolt will make it so the next owner cannot blame this on me.
Had to wack my half inch wrench with a hammer to get two of the drive shaft nuts started.
You do not have the required permissions to view the files attached to this post.
67 1600 (Mods only a mother could love)
78 911 SC Targa (Severe Oversteer but still loved)
78 911 SC Targa (Severe Oversteer but still loved)
- Curtis
- Site Supporter
- Posts: 4051
- Joined: Fri Jan 01, 2010 2:49 pm
- Location: Des Moines, WA
- Model: 1500/1600
- Year: Low Windshield-64-67.5
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
I took the whole morning to drive my frame and many other parts up north to Arlington, WA for black powder Friday. You get 20% off your powder coating.
And once again my frame mobility solution I built worked perfectly. Yes it's just a wood rack I built for the back of my Mazda pickup.
And once again my frame mobility solution I built worked perfectly. Yes it's just a wood rack I built for the back of my Mazda pickup.
66 stroker, almost done.
67 basket case, paint coming soon.
67 basket case, paint coming soon.
- RBMann
- Roadsteraholic
- Posts: 544
- Joined: Mon Jan 05, 2015 8:37 pm
- Location: Kenmore, WA
- Model: 1500/1600
- Year: High Windshield-68-70
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
Curtis-
Didn't happen without pictures.
Didn't happen without pictures.
RBMann
mechanic on '69-1600(not mine)
mechanic on '69-1600(not mine)
- Curtis
- Site Supporter
- Posts: 4051
- Joined: Fri Jan 01, 2010 2:49 pm
- Location: Des Moines, WA
- Model: 1500/1600
- Year: Low Windshield-64-67.5
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
Thought about a picture but didn't bother. When I get it back then that will be picture time.RBMann wrote:Curtis-
Didn't happen without pictures.
Worked on the braces for my body tipping jig today. Plan to weld them up tomorrow and try it out. Should make getting the undercoat off much easier with the body tipped up.
66 stroker, almost done.
67 basket case, paint coming soon.
67 basket case, paint coming soon.
- Curtis
- Site Supporter
- Posts: 4051
- Joined: Fri Jan 01, 2010 2:49 pm
- Location: Des Moines, WA
- Model: 1500/1600
- Year: Low Windshield-64-67.5
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
I finished my body tipping jig today. Now I can get the undercoat off.
You do not have the required permissions to view the files attached to this post.
66 stroker, almost done.
67 basket case, paint coming soon.
67 basket case, paint coming soon.
-
- Roadster Fanatic
- Posts: 273
- Joined: Tue Oct 04, 2016 8:26 pm
- Location: Laguna Beach,Ca.-USA
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
Interesting method. How sturdy did it feel on roll over?Curtis wrote:I finished my body tipping jig today. Now I can get the undercoat off.
73' Datsun 240-Z turbo
70' Datsun SRL-311-1374-SR20det 6 speed
69' Datsun SRL-311-12334-Solex 44 w/B cam
07' BMW Z4 coupe-Daily
70' Datsun SRL-311-1374-SR20det 6 speed
69' Datsun SRL-311-12334-Solex 44 w/B cam
07' BMW Z4 coupe-Daily
- Curtis
- Site Supporter
- Posts: 4051
- Joined: Fri Jan 01, 2010 2:49 pm
- Location: Des Moines, WA
- Model: 1500/1600
- Year: Low Windshield-64-67.5
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
Good, it has steel braces that bolt to the inside of the body. I lifted it most of the way with the engine lift and then tipped it the rest. I started to just lift it by hand but it was a bit too much. Saw a mustang and others on YouTube that used this method. One guy made a roller one for his VW bus. Saw a wood roller too.Vinnyz wrote:Interesting method. How sturdy did it feel on roll over?Curtis wrote:I finished my body tipping jig today. Now I can get the undercoat off.
https://www.youtube.com/watch?v=FzPzO6ECh8c
I could have rented a rotisserie from one of the local roadster owners but I would have had to make the mounting brackets. Plus the rotisserie takes up more room.
I got about half the undercoat off today.
Last edited by Curtis on Tue May 30, 2017 10:40 am, edited 1 time in total.
66 stroker, almost done.
67 basket case, paint coming soon.
67 basket case, paint coming soon.
- Lorna c
- Site Supporter
- Posts: 2428
- Joined: Sat Aug 20, 2016 12:47 am
- Location: central coast , ,ca
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
I re-tuned it after putting in a frankenheader, put in new gas lines lowered my tire pressure from 32 to 27.lbs //. I like this spot the best /./. Haven't gone to the recommended 21 yet , I haven't done the math on difference in tire size from stock.
"Is it me, or does everyone want to race ?"
late 68 1600 3 main motor .
- Lorna c
- Site Supporter
- Posts: 2428
- Joined: Sat Aug 20, 2016 12:47 am
- Location: central coast , ,ca
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
This I'm doing for him !! New veins and idk what you call the fan belt ? Lungs ? haha
You do not have the required permissions to view the files attached to this post.
"Is it me, or does everyone want to race ?"
late 68 1600 3 main motor .
- Cyclewrks
- Roadster Fanatic
- Posts: 119
- Joined: Wed Feb 03, 2016 1:30 am
- Location: Nashville, TN area
- Model: 1500/1600
- Year: High Windshield-68-70
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
Got most of the fab work done on my battery tray/ remote battery switch setup done today.
You do not have the required permissions to view the files attached to this post.
"Life is not a journey to the grave intent to arrive safely in a pretty, well preserved body-but rather arriving in a broadside skid, thoroughly used up, totally worn out and loudly proclaiming "Damn, what a friggin ride!"- Anon
'70 1600
'70 1600
- msampsel
- Roadster Nut-Site Supporter
- Posts: 1812
- Joined: Mon Jul 14, 2014 5:31 pm
- Location: SoAZ
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
Cyclewrks wrote:Got most of the fab work done on my battery tray/ remote battery switch setup done today.
IMG_0206.JPG
Interesting, where will your battery sit when done?
Is this for a race?
67 1600 (Mods only a mother could love)
78 911 SC Targa (Severe Oversteer but still loved)
78 911 SC Targa (Severe Oversteer but still loved)
-
- Roadster Newby
- Posts: 23
- Joined: Mon Apr 03, 2017 8:23 am
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
Put new wheels and tires on the Datsun.
You do not have the required permissions to view the files attached to this post.
- notoptoy
- Vendor-Site Supporter
- Posts: 9677
- Joined: Fri Oct 02, 2009 2:55 pm
- Location: Winston-Salem, NC and Ocala, FL
- Contact:
Re: What did you do TO or FOR your Datsun today?(Roadsters only)
I like it, kind of a Porsche vibe going on there. The front end seems kind of high though. How about some pictures of your interior?
"When all else fails, force prevails!" Ummm, we're gonna need a bigger hammer here.
67.5 SPL311 H20 w/5 speed
65 Impala Convertible
2017 C43 AMG
67.5 SPL311 H20 w/5 speed
65 Impala Convertible
2017 C43 AMG