Page 1 of 5
Pat's Sr20 Project
Posted: Sat Dec 08, 2012 8:22 pm
by dynaguy
I'm not very good at documenting my project, but here are a couple of pics of my progress so far. The engine and tranny are mounted in the frame and the rx7 rear end is bolted up. Kudos to the Spriso crew, everything bolted up perfectly and looks better than factory!
Pat Mahoney
Re: Pat's Sr20 Project
Posted: Sat Dec 08, 2012 11:36 pm
by notoptoy
Very nice, and very clean!
Re: Pat's Sr20 Project
Posted: Sat Dec 08, 2012 11:44 pm
by Alvin
super tasty
hey where did you get all those nuts and bolts from
Re: Pat's Sr20 Project
Posted: Sun Dec 09, 2012 12:43 am
by L320
WOW! Very nice!
Dale - AZ
Re: Pat's Sr20 Project
Posted: Sun Dec 09, 2012 6:47 am
by bobd
S13?
Any sources on a distributor rotor?
Re: Pat's Sr20 Project
Posted: Sun Dec 09, 2012 4:08 pm
by Ed Mason
Very nice!
Did you keep the disc brake backing plates on the mazda rearend? And what size wheels and offset did you use. I finally found and purchased a gsl-se rearend for my swap. Don't know yet how to deal with the roadster 1600 driveline flange to mazda differential flange. Just waiting to pull the pieces off the datsun rearend, mazda housing already stripped and ready to ship to Michael.
Swap looks great so far, what engine series did you use? Keep up the good work.
Re: Pat's Sr20 Project
Posted: Sun Dec 09, 2012 11:06 pm
by dynaguy
Ed,
You will need to keep the backing plates. Michael can help you with how to prep those and your driveline. My wheels are Rota RBs 15x7+12offset, tires are 195/50. They should fit without body mods.
My engine is a s13sr20. The drivetrain came with the "Jigsaw Puzzle Project" I bought about 5 yrs. ago from a guy that gave up on the car. It was completely dissasembled, most of body work done.
I had the Spriso crew do the frame mods even before I saw what I purchased. The rx7 LSD rear, 300zx front brakes, and flat dash conversion with electronic gauges are upgrades to modernize my car.
Hope to take it to Shasta in 2014.
Pat Mahoney
Re: Pat's Sr20 Project
Posted: Mon Jan 14, 2013 9:07 am
by dynaguy
I did a little work on the bling factor this weekend. Had the dash film dipped with an aluminum mesh design and wanted to see how the new gauges would look. Here are the results.
Pat
Re: Pat's Sr20 Project
Posted: Mon Jan 14, 2013 9:11 am
by jamesw
Wow! That looks blingy Pat. Looks great.
James
Re: Pat's Sr20 Project
Posted: Mon Jan 14, 2013 9:42 am
by notoptoy
Wow, I like it, it has a very classy and classic look.
Re: Pat's Sr20 Project
Posted: Mon Jan 14, 2013 5:46 pm
by Gregs672000
Ya, that is going to look great with a nice dark pad.
Re: Pat's Sr20 Project
Posted: Mon Jan 14, 2013 10:12 pm
by twistin
two thumbs up !
Re: Pat's Sr20 Project
Posted: Tue Jan 15, 2013 12:13 am
by etroxel
beautiful!
Re: Pat's Sr20 Project
Posted: Sat Feb 22, 2014 9:50 am
by dynaguy
Back from paint!!!!!yea.
Re: Pat's Sr20 Project
Posted: Sat Feb 22, 2014 9:53 am
by notoptoy
That is going to be stunning! Congratulations!