Page 6 of 7
Re: I'm Bitten
Posted: Fri Nov 21, 2008 1:29 am
by waggleboy
slight vibration? i'll be flogging her to hard to notice....a friend said i should really do the balance....thanks for the 2nd
any way. the intake is mostly ready for install.
tune them carbs boys...
Re: I'm Bitten
Posted: Fri Nov 21, 2008 1:52 am
by waggleboy
can anyone tell me why theres a G and B adjustment on the carb linkage?
if you go to that outer most hole on the linkage, it's way to long
Re: I'm Bitten
Posted: Sun Nov 30, 2008 3:44 pm
by waggleboy
happy holidays.
the engine bay is painted. engines in work. rear brakes in work. clutch/brake hyd systems in work.
eng./tran scheduled to be installed 12/13/08.
still got a lot of work to do on this refresh.
Re: I'm Bitten
Posted: Thu Dec 04, 2008 1:42 am
by waggleboy
she's a bitch and on a deadline.....
Re: I'm Bitten
Posted: Thu Dec 04, 2008 7:33 am
by spl310
I hope that you are talking about the car and not Robin...
Re: I'm Bitten
Posted: Sun Dec 07, 2008 2:51 pm
by waggleboy
both of em. the 64 is still waiting.
the white one is is going back together. still shooting for the engine install next weekend.
hydraulics was a lot of fun. and the harness is in work as well.
Got a Question. Does header paint really work? it's sand blasted and clean metal now. i figure it's gotta have some kind of protection. checked on pro coatings. $150 i don't wanna spend.
started the engine build up as well.
Re: I'm Bitten
Posted: Sun Dec 07, 2008 2:59 pm
by waggleboy
my buddy Matt did a lil' weld repair for. some prior idiot hit something.
not sure what you call that leg where the sway bar attaches? but if you try this at home.....that metal is very thin.
Re: I'm Bitten
Posted: Sun Dec 07, 2008 3:09 pm
by waggleboy
srry......same pic
here's the before
Re: I'm Bitten
Posted: Mon Dec 15, 2008 1:56 am
by waggleboy
well, we didn't run 'er but got a whole lot done.
my utmost thanks go out to the following;
Robin, I wouldn't be here without you
Pete, ssry i wasn't quite prepared as last time.
Gordo, that throw out brg is gonna work like a champ and i will be visiting your web site about setting up this EI Dizzy.
Nicky, thank you so much for all that hard work underneafh. hope your back is ok?
Re: I'm Bitten
Posted: Mon Dec 15, 2008 2:09 am
by waggleboy
she's really going back together
Re: I'm Bitten
Posted: Mon Dec 15, 2008 4:32 pm
by spl310
Lookin good!!
Re: I'm Bitten
Posted: Mon Dec 15, 2008 7:39 pm
by Linda
So the Roadster Pals came thru? Congrats, nice progress.
Linda
Re: I'm Bitten
Posted: Wed Dec 24, 2008 1:32 am
by waggleboy
she runs!
Happy Holidays
Re: I'm Bitten
Posted: Sun Jan 11, 2009 6:37 pm
by waggleboy
took some time off for the holidays
the enginebay is damn near done. trying to get the brakes done to make her roadworthy.
NWDE has it's 1st '09 meeting friday night. Not sure she'll be ready.
Re: I'm Bitten
Posted: Sun Jan 11, 2009 8:25 pm
by spl310
Looks first rate! Aren't you glad you cleaned up the bay while you were in there?