Re: Garm's 1969 project
Posted: Wed May 23, 2012 3:34 am
Eastbound on ramp video please!!
My butt says yes. I'll dyno it again when I get the cam on there.
Datsun Roadster Forum-311s.org
The Resource For All Things Datsun Roadster S211/SPL212/310/311 Datsun Sports Roadster 1959-April 1970 circa 40,000 produced
https://www.311s.org/phpBB3/
Garm's 1969 project
Page 18 of 46
Re: Garm's 1969 project
Posted: Wed May 23, 2012 9:12 am
@ pebbles: that's a great idea. I'll do it today.
My butt says yes. I'll dyno it again when I get the cam on there.
My butt says yes. I'll dyno it again when I get the cam on there.
Re: Garm's 1969 project
Posted: Wed May 23, 2012 9:41 am
Good job on the coil and wires. I could feel a difference with the MSD wire and coil I used too.
Linda
Linda
Re: Garm's 1969 project
Posted: Wed May 30, 2012 10:18 am
Part #??Garm wrote:Bye bye heater hoses, coolant lines etc. Got the front half (the easy half) done. Plugs are 3/8" BPT from Grainger.
Re: Garm's 1969 project
Posted: Wed May 30, 2012 10:36 am
^ 4CCP4
http://www.grainger.com/Grainger/ADAPTA ... Plug-4CCP4" onclick="window.open(this.href);return false;" onclick="window.open(this.href);return false;
http://www.grainger.com/Grainger/ADAPTA ... Plug-4CCP4" onclick="window.open(this.href);return false;" onclick="window.open(this.href);return false;
Re: Garm's 1969 project
Posted: Wed May 30, 2012 10:56 am
^ Thanks Garm!!
Re: Garm's 1969 project
Posted: Wed May 30, 2012 12:56 pm
Just ordered two of the cheap version of the cup holder, will let you all know if they are crap or decent. Feedback looked good, and for less than ten bucks for two it seemed like a no-brainer!
Re: Garm's 1969 project
Posted: Wed May 30, 2012 3:01 pm
Can't wait to see!
Re: Garm's 1969 project
Posted: Wed May 30, 2012 9:35 pm
You aught to add the heater hose block offs to the PMWIKI tech section. I am sure there are plenty of people that would love to easily find that info down the road! (Like myself)
Re: Garm's 1969 project
Posted: Wed May 30, 2012 10:48 pm
hmm, alright, glad to submit that info
Re: Garm's 1969 project
Posted: Thu May 31, 2012 12:59 am
I just ordered 4 block off pipe plugs today!!
Re: Garm's 1969 project
Posted: Fri Jun 08, 2012 8:58 am
Developed a water pump leak. This was just as difficult to remove as the thermostat housing was.
Finally got my cutoff tool out. Muahaha! Win!
Finally got my cutoff tool out. Muahaha! Win!
Re: Garm's 1969 project
Posted: Fri Jun 08, 2012 9:01 am
That is going to be a little difficult to rebuild...
Re: Garm's 1969 project
Posted: Fri Jun 08, 2012 10:49 am
Duct tape.
Re: Garm's 1969 project
Posted: Fri Jun 08, 2012 10:54 am
Super glue, and a coat hanger. But use anti-sieze!