I'm Bitten

waggleboy · Post by **waggleboy** » Fri Nov 21, 2008 1:29 am

slight vibration? i'll be flogging her to hard to notice....a friend said i should really do the balance....thanks for the 2nd

any way. the intake is mostly ready for install.

tune them carbs boys...

waggleboy · Post by **waggleboy** » Fri Nov 21, 2008 1:52 am

can anyone tell me why theres a G and B adjustment on the carb linkage?

if you go to that outer most hole on the linkage, it's way to long

waggleboy · Post by **waggleboy** » Sun Nov 30, 2008 3:44 pm

happy holidays.

the engine bay is painted. engines in work. rear brakes in work. clutch/brake hyd systems in work.

eng./tran scheduled to be installed 12/13/08.

still got a lot of work to do on this refresh.

waggleboy · Post by **waggleboy** » Thu Dec 04, 2008 1:42 am

she's a bitch and on a deadline.....

Post by **spl310** » Thu Dec 04, 2008 7:33 am

I hope that you are talking about the car and not Robin...

waggleboy · Post by **waggleboy** » Sun Dec 07, 2008 2:51 pm

both of em. the 64 is still waiting.

the white one is is going back together. still shooting for the engine install next weekend.

hydraulics was a lot of fun. and the harness is in work as well.

Got a Question. Does header paint really work? it's sand blasted and clean metal now. i figure it's gotta have some kind of protection. checked on pro coatings. $150 i don't wanna spend.

started the engine build up as well.

waggleboy · Post by **waggleboy** » Sun Dec 07, 2008 2:59 pm

my buddy Matt did a lil' weld repair for. some prior idiot hit something.

not sure what you call that leg where the sway bar attaches? but if you try this at home.....that metal is very thin.

waggleboy · Post by **waggleboy** » Sun Dec 07, 2008 3:09 pm

srry......same pic

here's the before

waggleboy · Post by **waggleboy** » Mon Dec 15, 2008 1:56 am

well, we didn't run 'er but got a whole lot done.

my utmost thanks go out to the following;

Robin, I wouldn't be here without you

Pete, ssry i wasn't quite prepared as last time.

Gordo, that throw out brg is gonna work like a champ and i will be visiting your web site about setting up this EI Dizzy.

Nicky, thank you so much for all that hard work underneafh. hope your back is ok?

waggleboy · Post by **waggleboy** » Mon Dec 15, 2008 2:09 am

she's really going back together

Post by **spl310** » Mon Dec 15, 2008 4:32 pm

Lookin good!!

Post by **Linda** » Mon Dec 15, 2008 7:39 pm

So the Roadster Pals came thru? Congrats, nice progress.

Linda

waggleboy · Post by **waggleboy** » Wed Dec 24, 2008 1:32 am

she runs!

Happy Holidays

waggleboy · Post by **waggleboy** » Sun Jan 11, 2009 6:37 pm

took some time off for the holidays

the enginebay is damn near done. trying to get the brakes done to make her roadworthy.

NWDE has it's 1st '09 meeting friday night. Not sure she'll be ready.

Post by **spl310** » Sun Jan 11, 2009 8:25 pm

Looks first rate! Aren't you glad you cleaned up the bay while you were in there?

Datsun Roadster Forum-311s.org

I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten

Re: I'm Bitten