Square grommet on glove box door

[Habitat.pat]

I remember reading some posts about the square grommet on the glove box door support that someone was looking for (me too).
Someone said they would look at 3D printing some but I can't find the thread. Has any progress been made on it yet? Where is the thread?

Peace,
Pat

[Curtis]

I made a 3D file but would have to see if it is usable by someone with a 3D printer. I got a used one for now.

[iloveredmeat]

I remember reading some posts about the square grommet on the glove box door support that someone was looking for (me too).
Someone said they would look at 3D printing some but I can't find the thread. Has any progress been made on it yet? Where is the thread?

Peace,
Pat

I made a 3D file but would have to see if it is usable by someone with a 3D printer. I got a used one for now.

Pat, I remember seeing something about that too... it's gotta be here somewhere.

Curtis, if it's no trouble to email that file, I can forward it to a friend for review and ask if they'd be willing to run a few.

I think (hope!) I also have my original grommet. I remember it being in decent condition... I will post a photo here if I find it while working through the Ice Cooler O' Parts...



Thanks,
Peter

[Curtis]

Probably disappeared because it was a wanted post. I think Solex68 replied about printing it.

[garth]

Contact Ross @ Sports Imports. He has a warehouse full of new rubber parts. If he does not have new he can fab or source a quality replacement.

[Curtis]

Contact Ross @ Sports Imports. He has a warehouse full of new rubber parts. If he does not have new he can fab or source a quality replacement.

Ross is where I got my used one. He had a hard time getting it out unbroken, wasted a half hour on it for me. It is not rubber but a rectangular plastic piece.

[goldbug]

Could you post the 3D file somewhere Curtis? (can be emailed if that's preferred)

My printer is currently idle; I can take a stab at printing it (not really set up for mass production, but would be interesting nonetheless)

[redroadster]

Mitsubishi used many a square plastic blind clip
Tiny, medium, & large

[Curtis]

Mitsubishi used many a square plastic blind clip
Tiny, medium, & large

Except it's not square.

IMG_3014.JPG

IMG_3015.JPG

[Habitat.pat]

Thanks to all who replied. I thought it was rubber that had just hardened over time.I have a usable one to use....if I can find it!

Be well.

Peace,
Pat

[Curtis]

We really need to get this one made. I'll have to look at my file and if it can be used at all. Used ones kind of suck.

[goldbug]

Went out and checked mine: it was already cracked on a corner so I pulled it out to measure/print.

This little guy, right?


Looked at CPM, and I saw two different part numbers for early vs. late dashes. Mine came off a late dash, and it seems to be made out of a semi-flex type rubbery plastic. I'm going to print up some test versions (might need to improvise a clip for the back if the "barb" edge isn't enough).

Curtis, is your 3d/measurement from early or late?

[goldbug]

A quick first pass at it:


In photos it doesn't look exactly the same size as the original, but that's mostly due to the OG being cracked/bent. Side by side they feel the same (should be roughly within 0.1mm). I added some gaps in the barb/skirt on the back to let it flex a little when inserting (this was rando plastic I already had loaded in my printer; wouldn't use it for final print). I'm planning on going back in and tweaking it a little from "OEM" dimensions to make the print path a little cleaner and let the barbs flex a little more. Otherr subtle changes: turned some of the edge relief from a round fillet to a chamfer-- this is hidden normally, didn't think perfect OEM match was something worth chasing.

Test fit: it's a hair too tight/rigid to fit. Will tweak and retry.

Also: the crap filament also snapped 2/3 through the print, so that didn't help (resumed ever so slightly off).

[notoptoy]

Nice work!

[iloveredmeat]

This is awesome.