Radiator Question

Tech tips and how to's

Moderators: notoptoy, S Allen, Solex68

bradleygt
Site Supporter
Posts: 14
Joined: Fri Jan 16, 2015 12:32 pm
Location: Boise, Idaho
Model: 1500/1600
Year: Low Windshield-64-67.5

Radiator Question

Post by bradleygt »

Hello,
Restoring a 1966 Datsun 1600 all stock. The question is to have the original radiator cleaned / rotted out which is around $100.00 dollars, or is it better to just go and get a champion radiator and if so 2 or 3 rows? This car has been sitting for over 20 years. My wife uncle bought the car new in 1966 and as far as I can find out it didn't have any overheating issues. There is 85000 mile on the car. Any input would be greatly appreciated.
Thanks Brad Johnson
User avatar
spl310
Roadster Guru
Posts: 13202
Joined: Sun Dec 29, 2002 10:38 pm
Location: In front of this keyboard... in Jacksonville, Florida!

Re: Radiator Question

Post by spl310 »

Well, do you want it to be stock or not? Stock is a brass radiator. The Champion looks completely different. Either way works.
"Wow, a Roadster!" Stuart Little

1967.5 2000
1967.5 2000
1964 1500
1964 1500
1967.5 1600
1968 chassis
2006 Acura MDX
2013 Volkswagen Jetta TDI wagon
1995 F350 Powerstroke!
More...
bradleygt
Site Supporter
Posts: 14
Joined: Fri Jan 16, 2015 12:32 pm
Location: Boise, Idaho
Model: 1500/1600
Year: Low Windshield-64-67.5

Re: Radiator Question

Post by bradleygt »

Doesn't have to be stock. More interested in what ever works well and looks good.
Thanks Brad
User avatar
spl310
Roadster Guru
Posts: 13202
Joined: Sun Dec 29, 2002 10:38 pm
Location: In front of this keyboard... in Jacksonville, Florida!

Re: Radiator Question

Post by spl310 »

Either works fine. Looks are subjective. Decide which look you like and go for it. Research how the Champion fits as I don't recall which year radiator they used as a model.
"Wow, a Roadster!" Stuart Little

1967.5 2000
1967.5 2000
1964 1500
1964 1500
1967.5 1600
1968 chassis
2006 Acura MDX
2013 Volkswagen Jetta TDI wagon
1995 F350 Powerstroke!
More...
greydog
Roadster Fanatic-Site Supporter
Posts: 1790
Joined: Sat Nov 21, 2009 11:37 pm
Location: Vancouver, Washington
Model: 1500/1600
Year: High Windshield-68-70

Re: Radiator Question

Post by greydog »

If cared for (occasional coolant flushes and actual coolant use instead of just water) the stock radiator/fan/shroud works fine. I'd have the radiator pressure tested and checked to make sure the coolant circulates satisfactorily.
If it checks out ok, I'd use the factory radiator for as long as practical.
In fact, I put a 2000 radiator in our 1600. Not for extra cooling but for the more "regular" fill/inlet configuration. That allowed me to make a bunch of changes. I eliminated the fill/thermostat tower, removed the fan and spacers, installed an electric fan and generally "modernized" the front of the engine bay.
Point is, the factory cooling system, including the radiator , works fine if in good repair. There's no good reason to change it unless it's failing or you want to for some other reason.
Dan
SPL311 aka Skooter. Sold. Now wasting away in the SF area.
1990 Nissan 300zx. Sold this one too.
2018 VW Tiguan
User avatar
Nissanman
Roadster Fanatic-Site Supporter
Posts: 3350
Joined: Mon Apr 16, 2007 8:07 pm
Location: Adelaide, South Australia
Model: 1500/1600
Year: Low Windshield-64-67.5
Contact:

Re: Radiator Question

Post by Nissanman »

"Point is, the factory cooling system, including the radiator , works fine if in good repair".
Very dependent on your local climate.
In Oz, our Summers are very hot and the OEM system in my SP310 was inadequate.
I don't know what your weather is like in Boise but just bear it in mind :)
Nissanman, just trying to help.
1965 SP310 Engine No. G-93326 Car No. SP310-10817
https://photos.shutterfly.com/album/60141836519
On the road again!
devo
Roadsteraholic
Posts: 535
Joined: Mon Jun 17, 2013 7:58 pm
Location: Texas
Model: 1500/1600
Year: Low Windshield-64-67.5

Re: Radiator Question

Post by devo »

bradleygt wrote: Wed Feb 13, 2019 2:56 pm Hello,
Restoring a 1966 Datsun 1600 all stock. The question is to have the original radiator cleaned / rotted out which is around $100.00 dollars, or is it better to just go and get a champion radiator and if so 2 or 3 rows? This car has been sitting for over 20 years. My wife uncle bought the car new in 1966 and as far as I can find out it didn't have any overheating issues. There is 85000 mile on the car. Any input would be greatly appreciated.
Thanks Brad Johnson
I put this one in my wife's '66 and it works great. It is for a 2L motor and you will have to replace the thermostat tower with a standard water neck (3 bolt from an 81-83 sd22 motor from a Nissan 720 truck). They also have a 1600 version for about the same price if you want to keep the standard thermostat tower.

https://www.ebay.com/itm/FOR-NISSAN-DAT ... k:170:pf:0

Here is the 1600 version for no mods.

https://www.ebay.com/itm/ALUMINUM-RADIA ... :rk:1:pf:0
Last edited by devo on Thu Feb 14, 2019 8:06 am, edited 2 times in total.
C.Costine
Roadster Nut-Site Supporter
Posts: 1731
Joined: Fri Feb 13, 2015 8:08 pm

Re: Radiator Question

Post by C.Costine »

Brad, I drove a '67.5 from late 1969 to 1972. They were known for overheating and head gasket failures. However, good maintenance can make it a lot less likely. I am putting a '67 back together now and I am planning to use the stock, though recent radiator. You need to just be mindful of maintaining it. I would get it cleaned and rodded out by a shop, and keep in mind that it will tend to overheat in stop and go traffic.
located in Chester NH
1967 1600 in restoration
2013 Arctic Cat F-1100 turbo
Ford F-350 6.0
Ford 9000 puller, Ford 960 puller, Ford 901show, Ford 971 worker, Oliver 70 waiting its turn
User avatar
david premo
Roadster Nut-Site Supporter
Posts: 653
Joined: Wed Jan 24, 2007 8:23 am
Location: Southern Oregon
Model: 2000
Year: Low Windshield-64-67.5
Contact:

Re: Radiator Question

Post by david premo »

The radiator shop can install a close ratio core, more tubes per inch going across. That is what the OE Nissan radiator came as and many radiator shops need to be told you want the close ratio core or they install a standard core with less rows.
User avatar
keith0alan
Roadsteraholic
Posts: 904
Joined: Wed Sep 22, 2004 10:07 am

Re: Radiator Question

Post by keith0alan »

Agreed, have your stock radiator recored with a high density core. Stock look and better cooling.
User avatar
redroadster
Roadsteraholic
Posts: 2383
Joined: Tue Mar 12, 2013 10:58 am
Location: KCMO
Model: 1500/1600
Year: High Windshield-68-70

Re: Radiator Question

Post by redroadster »

I always want mine Rodded out if it can be , i have been burnt with the rot outs
Rod out means. A tank is removed from the core and a music wire rod is pushed thru the coolant tube then checked. By seeing the water fall thru the tubes
Last edited by redroadster on Fri Mar 06, 2020 9:18 am, edited 1 time in total.
Datsun dealer tech 76 to 87
Mitsubishi tech 9 yrs
Volvo, Kia, Toyota too
6 month - Rolls Royce
ASE MASTER TECH 96. - 11
70 SPL 86 Z31 T , Sportster
User avatar
keith0alan
Roadsteraholic
Posts: 904
Joined: Wed Sep 22, 2004 10:07 am

Re: Radiator Question

Post by keith0alan »

One problem is that the fins are soldered to the tubes. As time goes by the solder joints come loose. It will look fine but heat transfer is way down. It will flow great but not cool very well.
User avatar
Linda
Fraternal Den Mother-RIP
Posts: 7807
Joined: Sat Nov 05, 2005 11:37 pm
Location: Los Angeles
Model: 1500/1600
Year: High Windshield-68-70

Re: Radiator Question

Post by Linda »

Might want to consider checking the block for rust. Clearing it out is a hassle but it is part of the cooling system. There can be a surprising amount of deposits in there
Linda
Sadly-Linda has passed away 2022. She was the 311's den mother and drove the first Rare-Parts ball joint project. RIP.
User avatar
dads311
Roadster Fanatic-Site Supporter
Posts: 203
Joined: Sun Dec 04, 2016 9:24 pm
Location: Emmett, Id.
Model: 1500/1600
Year: Low Windshield-64-67.5

Re: Radiator Question

Post by dads311 »

Brad, you might want to take your radiator to a shop and have them evaluate it. If you can get away with just getting it rodded out, great. If it need recored let me know, I have a couple here we could check out as well as a couple shrouds. I went with a new aluminum 2 core radiator for mine with an electric fan. And while this was my dads car since 1969 I wasn't concerned about originality, and the cost was about the same. Since I just went through a restoration on a 67.5 I would be more than happy to help you out if I can, especially since you are just over the hill from me.
Mike
Mike
rebuilt dads 67.5 1600
1952 GMC 302ci 6cyl w/cam and 3 deuces
1965 Mustang (Wife's)
1971 Nova (Son Claimed)
bradleygt
Site Supporter
Posts: 14
Joined: Fri Jan 16, 2015 12:32 pm
Location: Boise, Idaho
Model: 1500/1600
Year: Low Windshield-64-67.5

Re: Radiator Question

Post by bradleygt »

Would like to thank everyone that chimed in. Got some good ideas, just have to decide which way to go. Plus it's nice to have another Datsun person that is just over the hill from me.
Thanks Brad

P.S. Nice to have this forum to go to for questions and ideas.
Post Reply