2000 axle clearance
Moderators: notoptoy, S Allen, Solex68
-
- Forum Newb
- Posts: 4
- Joined: Wed Dec 06, 2017 9:46 am
2000 axle clearance
installing new bearings and seals on 2000 rear axle, I am in need of axle end clearance. I have two manuals neither are spacific to 311
Thank You
Kilro
Thank You
Kilro
- BBF Roadster
- Roadster Fanatic
- Posts: 222
- Joined: Thu Oct 20, 2011 8:30 pm
- Location: Houston TX
Re: 2000 axle clearance
Does anyone know where to buy just the shims.
67.5 1600, U20 Swap
69 GTO
70 Barracuda
70 Roadrunner
70 Mustang FB
71 GMC Sprint SP 454
72 El Camino SS 454
69 GTO
70 Barracuda
70 Roadrunner
70 Mustang FB
71 GMC Sprint SP 454
72 El Camino SS 454
- notoptoy
- Vendor-Site Supporter
- Posts: 9677
- Joined: Fri Oct 02, 2009 2:55 pm
- Location: Winston-Salem, NC and Ocala, FL
- Contact:
Re: 2000 axle clearance
McMaster Carr has a nice listing of shims in various sizes, and any reputable bearing supplier should be able to come up with a suitable alternative.
"When all else fails, force prevails!" Ummm, we're gonna need a bigger hammer here.
67.5 SPL311 H20 w/5 speed
65 Impala Convertible
2017 C43 AMG
67.5 SPL311 H20 w/5 speed
65 Impala Convertible
2017 C43 AMG
- Linda
- Fraternal Den Mother-RIP
- Posts: 7807
- Joined: Sat Nov 05, 2005 11:37 pm
- Location: Los Angeles
- Model: 1500/1600
- Year: High Windshield-68-70
Re: 2000 axle clearance
Last edited by Linda on Wed Mar 28, 2018 2:07 pm, edited 1 time in total.
Sadly-Linda has passed away 2022. She was the 311's den mother and drove the first Rare-Parts ball joint project. RIP.
- fj20spl311
- Roadsteraholic
- Posts: 5014
- Joined: Mon Nov 28, 2005 3:54 pm
- Location: San Diego, Ca
Re: 2000 axle clearance
"The one- to five-thou range is a compromise between too loose and too tight, At zero, we're into preload and we can't measure that. Between zero and one thou, we could be measuring deflection and still be in preload. Between one and five, we know the bearing is not preloaded, and it's not too loose that it will cause other problems downstream. I usually find the clearance and then shim it out to 0.00 to 0.001 preload.
Phil
67.5 SRL311-00148 Blue (FJ cruiser VOODOO Blue)
67.5 SPL311 FJ20E teal SDS EFI
69 SRL311 SOLD
19 Raptor SCAB
67.5 SRL311-00148 Blue (FJ cruiser VOODOO Blue)
67.5 SPL311 FJ20E teal SDS EFI
69 SRL311 SOLD
19 Raptor SCAB
-
- Forum Newb
- Posts: 4
- Joined: Wed Dec 06, 2017 9:46 am
Re: 2000 axle clearance
Thank you Phil for the information, assembled axle with new bearings and seals. I have two axles 1966 and 69 both had four shims that were .oo3 installed two shims on each side and dial indicated. End clearance indicated at about .004 both sides and I am comfortable going with that. what was giving me an issue is someone had worked on 69 axle and installed 3 shims on one side and 1 on the other. There is no substitute for experience .
Thank you again
kilro
Thank you again
kilro
- BBF Roadster
- Roadster Fanatic
- Posts: 222
- Joined: Thu Oct 20, 2011 8:30 pm
- Location: Houston TX
Re: 2000 axle clearance
Notoptoy
How would I cut the shims from a sheet and add the correct shape with add holes.
Thanks
How would I cut the shims from a sheet and add the correct shape with add holes.
Thanks
67.5 1600, U20 Swap
69 GTO
70 Barracuda
70 Roadrunner
70 Mustang FB
71 GMC Sprint SP 454
72 El Camino SS 454
69 GTO
70 Barracuda
70 Roadrunner
70 Mustang FB
71 GMC Sprint SP 454
72 El Camino SS 454
- notoptoy
- Vendor-Site Supporter
- Posts: 9677
- Joined: Fri Oct 02, 2009 2:55 pm
- Location: Winston-Salem, NC and Ocala, FL
- Contact:
Re: 2000 axle clearance
I did not suggest cutting from sheets, McMaster Carr carries many “stock†sizes, though I only considered round. Sheet stock is thin enough where I am sure a regular/heavy duty pair of scissors could be used effectively.
"When all else fails, force prevails!" Ummm, we're gonna need a bigger hammer here.
67.5 SPL311 H20 w/5 speed
65 Impala Convertible
2017 C43 AMG
67.5 SPL311 H20 w/5 speed
65 Impala Convertible
2017 C43 AMG
- dynaguy
- Roadster Fanatic-Site Supporter
- Posts: 1218
- Joined: Wed Jan 01, 2003 3:27 pm
- Location: Colton, Wa
Re: 2000 axle clearance
I have some old axles that have shims on them. I can probably set you up with what you need. Pat
- BBF Roadster
- Roadster Fanatic
- Posts: 222
- Joined: Thu Oct 20, 2011 8:30 pm
- Location: Houston TX
Re: 2000 axle clearance
I have the old shims but they are a little rough.
Should a use them?
Should a use them?
67.5 1600, U20 Swap
69 GTO
70 Barracuda
70 Roadrunner
70 Mustang FB
71 GMC Sprint SP 454
72 El Camino SS 454
69 GTO
70 Barracuda
70 Roadrunner
70 Mustang FB
71 GMC Sprint SP 454
72 El Camino SS 454
- Linda
- Fraternal Den Mother-RIP
- Posts: 7807
- Joined: Sat Nov 05, 2005 11:37 pm
- Location: Los Angeles
- Model: 1500/1600
- Year: High Windshield-68-70
Re: 2000 axle clearance
Shim stock as mentioned can be cut with scissors , so that you can make new shims. The old ones on my car were disintegrating.
Linda
Linda
Sadly-Linda has passed away 2022. She was the 311's den mother and drove the first Rare-Parts ball joint project. RIP.
-
- Roadster Fanatic
- Posts: 89
- Joined: Sat Feb 01, 2014 10:11 am
- Location: Bentonville, AR
Re: 2000 axle clearance
I posted this over on FB to a similar question - worth repeating. I just went through this exercise, thanks to Linda for the extra shim stock!
Shims are NLA from Nissan - I cut them from shim stock.
If you go the same route, be aware that the factory shims are sized so that they are dimensionally smaller than the flange at the end of the axle tube they sit against by maybe 1mm all the way around. Such a thin piece of metal protruding from between the axle tube and the brake backing plate would be as sharp as a knife!
Minuscule details like this make me really appreciate the level of detail of those Nissan engineers went to.
Shims are NLA from Nissan - I cut them from shim stock.
If you go the same route, be aware that the factory shims are sized so that they are dimensionally smaller than the flange at the end of the axle tube they sit against by maybe 1mm all the way around. Such a thin piece of metal protruding from between the axle tube and the brake backing plate would be as sharp as a knife!
Minuscule details like this make me really appreciate the level of detail of those Nissan engineers went to.
- ppeters914
- Roadster Fanatic-Site Supporter
- Posts: 3075
- Joined: Mon Jun 28, 2004 5:51 pm
- Location: Lake Forest Park, WA (just north of Seattle)
- Model: 1500/1600
- Year: Low Windshield-64-67.5
Re: 2000 axle clearance
How do you find the clearance? Specific steps, please.fj20spl311 wrote: ↑Wed Mar 28, 2018 2:03 pm "The one- to five-thou range is a compromise between too loose and too tight, At zero, we're into preload and we can't measure that. Between zero and one thou, we could be measuring deflection and still be in preload. Between one and five, we know the bearing is not preloaded, and it's not too loose that it will cause other problems downstream.
I usually find the clearance and then shim it out to 0.00 to 0.001 preload.
Pete
-------------------------------------
'67 1600 - frame off started in 2014. Now I know why roadster projects take so long. What a stupid idea.
'66 1600 - parts car
'66 WPL411 ***SOLD***
A couple of Porsches, a RAV4 Hybrid, and a motorcycle
-------------------------------------
'67 1600 - frame off started in 2014. Now I know why roadster projects take so long. What a stupid idea.
'66 1600 - parts car
'66 WPL411 ***SOLD***
A couple of Porsches, a RAV4 Hybrid, and a motorcycle
- fj20spl311
- Roadsteraholic
- Posts: 5014
- Joined: Mon Nov 28, 2005 3:54 pm
- Location: San Diego, Ca
Re: 2000 axle clearance
Measure it with a dial indicator with the shims removed or measure the depth and bearing thickness with calipers.
Phil
67.5 SRL311-00148 Blue (FJ cruiser VOODOO Blue)
67.5 SPL311 FJ20E teal SDS EFI
69 SRL311 SOLD
19 Raptor SCAB
67.5 SRL311-00148 Blue (FJ cruiser VOODOO Blue)
67.5 SPL311 FJ20E teal SDS EFI
69 SRL311 SOLD
19 Raptor SCAB
- ppeters914
- Roadster Fanatic-Site Supporter
- Posts: 3075
- Joined: Mon Jun 28, 2004 5:51 pm
- Location: Lake Forest Park, WA (just north of Seattle)
- Model: 1500/1600
- Year: Low Windshield-64-67.5
Re: 2000 axle clearance
Sorry to be dense, but what is it? How would I do this with a dial indicator?
Again, depth of what? Where?fj20spl311 wrote: ↑Mon Jun 18, 2018 8:54 pm...or measure the depth and bearing thickness with calipers.
Pete
-------------------------------------
'67 1600 - frame off started in 2014. Now I know why roadster projects take so long. What a stupid idea.
'66 1600 - parts car
'66 WPL411 ***SOLD***
A couple of Porsches, a RAV4 Hybrid, and a motorcycle
-------------------------------------
'67 1600 - frame off started in 2014. Now I know why roadster projects take so long. What a stupid idea.
'66 1600 - parts car
'66 WPL411 ***SOLD***
A couple of Porsches, a RAV4 Hybrid, and a motorcycle