That's what I meant to say. The ground wire from the pertronix plate in the dizzy goes somwhere...just can't remember where.notoptoy wrote:The dizzie should be grounded from the block. I believe the ground for the pertronix comes from the breaker plate. I do not believe you need a separate ground outside of the little one for the breaker plate.
Petronix install how to?
Moderators: notoptoy, S Allen, Solex68
-
- Roadster Fanatic
- Posts: 244
- Joined: Wed Aug 07, 2013 12:06 pm
- Location: Baltimore, MD
Re: Petronix install how to?
1968 Datsun 1600
2005 MINI Cooper S
2005 MINI Cooper S
- Dcyco1
- Roadster Fanatic
- Posts: 245
- Joined: Thu Oct 15, 2009 1:02 pm
- Location: Batavia IL
Re: Petronix install how to?
So here is my main question about bypassing resistor, what happens to those wires? Is one side or the other connected to coil or are they joined together and then connected to coil? I don't have clear picture on how to bypass resistor. I have the wiring diagram and I'm not sure what is the correct wiring. I have already blown fuse since I obviously used the wrong wires.
1969 Datsun 2000
1996 WS6 Trans Am
2016 Maxima SR
1996 WS6 Trans Am
2016 Maxima SR
- pebbles
- Roadster Fanatic-Site Supporter
- Posts: 3925
- Joined: Thu Dec 16, 2010 12:00 am
- Location: Washington
Re: Petronix install how to?
You do not have the required permissions to view the files attached to this post.
David
"When we were standing next to the motor while on the dyno, and the motor hit VVL, eyes went watery.."
"When we were standing next to the motor while on the dyno, and the motor hit VVL, eyes went watery.."
- Dcyco1
- Roadster Fanatic
- Posts: 245
- Joined: Thu Oct 15, 2009 1:02 pm
- Location: Batavia IL
-
- Roadster Fanatic
- Posts: 244
- Joined: Wed Aug 07, 2013 12:06 pm
- Location: Baltimore, MD
Re: Petronix install how to?
Yeah I'm fairly sure I connected two wires together to bypass the resistor.
1968 Datsun 1600
2005 MINI Cooper S
2005 MINI Cooper S
- pebbles
- Roadster Fanatic-Site Supporter
- Posts: 3925
- Joined: Thu Dec 16, 2010 12:00 am
- Location: Washington
Re: Petronix install how to?
ME, Thanks Bill Cole for the ratsun link in the "Stranded" thread.
David
"When we were standing next to the motor while on the dyno, and the motor hit VVL, eyes went watery.."
"When we were standing next to the motor while on the dyno, and the motor hit VVL, eyes went watery.."
-
- Roadster Fanatic
- Posts: 117
- Joined: Mon Sep 28, 2015 12:58 pm
Re: Petronix install how to?
So I'm installing a Pertronix on my early 67. The wires are a bit different. I have an ignition black/white wire which I connect to the +ve side of the coil. I had a black wire that went to my resistor? Where do I connect it? Also, what do I do with the black ground wire that was connected to the dizzy, which I read you disconnect from the dizzy? The picture shows the three wires, with the ground wire that was connected to the dizzy in my fingers.
[/URL][/img]
[/URL][/img]
-
- Roadster Fanatic
- Posts: 117
- Joined: Mon Sep 28, 2015 12:58 pm
Re: Petronix install how to?
Found my solution thanks to another user. The Black/White wire is the ignition wire which connects to the +ve side of the coil (which has a 3ohm resister built in). The wire in my hand is the ground wire which leads to the other black wire (which is the same wire) a ground wire. Simply tape these aside. Therefore I will have the red pertronix wire with the black/white wire to the +ve side of the coil, and the negative has the black pertronix wire. Hope this helps you.