What did you do TO or FOR your Datsun today?(Roadsters only)

[msampsel]

[quote="pebbles"]^ i wish!
HW
[url=http://s1301.photobucket.com/user/David ... c.jpg.html][img]http://i1301.photobucket.com/albums/ag1 ... ca163c.jpg[/img][/url][/quote]

Lovely for sure, what goes in the little hole? Not familiar I am ... must be the shift pattern, just surprised to see a hole
rather than indentation.

[msampsel]

I drilled holes in the passenger side of the engine compartment to mount an impact cutoff switch (part in the red box).

P1030509.JPG

Also routed wires and ready to go after painting the compartment is done.

Switch will cut the power to my electric fuel pump on impact. Making my roadster safer.
The switch is simple and allows for additional power to be supplied for an override. Using the fog
light switch for this ...

Will publish pictures once the side is painted and it is installed.

Cheers

[C.Costine]

I finished welding in the new right rocker panel, pod and bottom front of rear fender.

image.jpg

image.jpg

[krispoulin]

I got a new exhaust, from the headers back. I've done pretty much all of the work on this car myself, but paid a pro for this one. Gone is the exhaust rattle that drove me nuts. Gone is the change in exhaust note every time I hit a bump, due to small crack/hole in pipe. The car actually sounds like a sports car now and the rust-colored tailpipes are just a bad memory.

[pebbles]

I finished welding in the new right rocker panel, pod and bottom front of rear fender.

Nice work!

[RBMann]

Replaced the contacts part of the ignition switch on a '69-1600. One or two loose rivets. Exact fit but probably different country of origin.

http://www.ebay.com/itm/400701047695 $12.95

Rick

[S Allen]

Added ignition contacts to tech wiki-parts interchange. Nice find.

[Linda]

Check Rockauto for Standard Motor Products part 120
Igntion switch listed with photo- $21
Linda
https://www.rockauto.com/catalog/morein ... 98&jpid=17

[Zogster]

Nothing big but added the back up hood release today

[C.Costine]

Yesterday evening I started in on the hood. I knew that there would be some rust at each end of the front. I was not worried about that, but I was concerned about a crack in the paint running side to side in line with the front edge of the scoop over on the left edge. I removed the paint and filler with a 40 grit flapwheel in my grinder. removal of the paint revealed a gap in the factory lead filler under the crack in the paint. I got back at it this afternoon, and at this point I decided that it was getting serious so I went to my parts car, a 68 that I have had in storage since 1977. Removal of a little paint revealed that this one was a little worse. So it was back to the original hood. I needed to dig in so I started locating and sawing out spot welds and got the first piece out and it revealed this:

image.jpg

. Here I see that the front eight inches is lapped under the rest with about an inch and a half of overlap. It is sealed with lead on the top, but not sealed at all underneath, so it has been open to road mist for all of the time that it was on the road. So I see no way around blowing the lead off and opening it up and cleaning it. Removal of the lead revealed a big black rust opening at the seam.

image.jpg

I then removed half of the strengthening Chanel that runs front to back.

image.jpg

Locating the spot welds was difficult due to the rusted surface and cutting them out without going through the outer skin was difficult due to the thinness. But here is what it looks like now. The left side is separated and if I can get to it tomorrow I will be opening up the other side.

image.jpg

[msampsel]

Paint and more paint ... the easy stuff right?
And happy father's day too! Duplicolor is liking me I think ... . Thanks to guyatou for the tip on
the caliper paint too

P1030513.JPG

[mellis18]

Added some new wheels and tires, installed headlight and turn signals and installed antenna and some bling.

[pebbles]

Drained a pint of stinky gas from the 66 fuel tank. Did not have any new gas in the can
Drove to get some gas. Took the long way.

Kyak point


Marine vew drive



Warm Beach.

[Alvin]

Added some new wheels and tires, installed headlight and turn signals and installed antenna and some bling.

Those are the largest center caps I have ever seen! Please add your setup to the Wheel/tire thread

[msampsel]

Drained a pint of stinky gas from the 66 fuel tank. Did not have any new gas in the can
Drove to get some gas. Took the long way.

I think the title of the last pic should have been, "Ran in to pick up lottery tickets!"

Must be nice to be able to drive the '69 to get gas for the '66. Great views too!