What did you do TO or FOR your Datsun today?(Roadsters only)

msampsel · Post by **msampsel** » Sun Jun 07, 2015 1:08 am

Alvin wrote:I replaced my window squeegees today. It's been on my list for years and I finally bought a set along with the wing/frame squeegee from Dean.

My old window squeegees were torn and probably deteriorated from my sweaty arm hanging out over the years:

Definite improvement, I still need to do mine so I am a little envious.

msampsel · Post by **msampsel** » Wed Jun 10, 2015 5:29 pm

Well in a keeping up with the "Alvins" and my own WYAII (While Your at It Itis) I installed a squeegee today.
I notice a stress crack which must have occurred when I installed the vent window trim ... doh

P1030510.JPG

Not sure if I lost patina point here or not, but the old squeegee as pretty dilapidated

msampsel · Post by **msampsel** » Wed Jun 10, 2015 5:32 pm

And more of the WYAII continues ... just ordered this yesterday and it came today ... wow ...
looking for a home for the part on top of the battery ... while my block reads the paper waiting on its head ...

P1030509.JPG

cole455 · Post by **cole455** » Sat Jun 13, 2015 1:10 pm

Installed the drivetrain in mine!

Post by **notoptoy** » Sat Jun 13, 2015 6:45 pm

Nice, those Koni's are sitting pretty too.

Skyman · Post by **Skyman** » Sat Jun 13, 2015 7:13 pm

Awesome! Keeping an eye on the progress!

Post by **spl310** » Sat Jun 13, 2015 7:41 pm

I met with notoptoy and then came home and sawzalled the 68 2000 in preparation for its departure. Thinking about what all I need to do for my herd. Maybe I'll do a write-up of how I came to get my newest car...

Post by **notoptoy** » Sat Jun 13, 2015 7:58 pm

Write up would be good, more pictures even better!

Alvin · Post by **Alvin** » Sat Jun 13, 2015 11:16 pm

I took the hardtop off of my roadster today!

Post by **spl310** » Sat Jun 13, 2015 11:28 pm

I took a sawzall to the 69 parts car.

pebbles · Post by **pebbles** » Sun Jun 14, 2015 1:55 am

I stripped the vinyl off of the upper door trims,, then realized they were 67.5 bits...
DOH!
Got the 4sp shift plate right tho

msampsel · Post by **msampsel** » Sun Jun 14, 2015 6:45 am

pebbles wrote:I stripped the vinyl off of the upper door trims,, then realized they were 67.5 bits...
DOH!
Got the 4sp shift plate right tho

Well these is only one "right" shift plate for me so you must mean this one

must_look_like_this.jpg

What else could it be?

pebbles · Post by **pebbles** » Sun Jun 14, 2015 4:20 pm

^ i wish!
HW

Post by **bikermike** » Mon Jun 15, 2015 11:43 am

Cleared a blocked float valve in the rear carb and got right turn signal cancelling to work.

pebbles · Post by **pebbles** » Mon Jun 15, 2015 2:27 pm

Stripped the vinyl off of the correct trims, both cracked bummer.

Welded both

Blasted and Painted

Datsun Roadster Forum-311s.org

What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)