What did you do TO or FOR your Datsun today?(Roadsters only)

pebbles · Post by **pebbles** » Fri Jun 05, 2015 4:40 am

^ you change your oil every day?

Post by **C.Costine** » Fri Jun 05, 2015 6:00 am

Thanks guys for the tips on the vinyl. Hopefully temps will get above the low seventies here in NH before too long.

msampsel · Post by **msampsel** » Fri Jun 05, 2015 6:10 am

RCMike wrote:
spyder wrote:How do you change the oil filter without making a mess?
Will figure that out in 3000 miles..

Hey my Daughter's Subaru has a filter sitting the same way. It's cleaner to change than
the Montana, Roadster, Porsche, Avalon, Lexus and Camry all the oil falls out of it on its own before I remove it.

Post by **spl310** » Fri Jun 05, 2015 8:20 am

Let the oil drain out of the filter before you remove it.

msampsel · Post by **msampsel** » Fri Jun 05, 2015 9:36 am

I spent the last several days applying JB weld epoxy to my carb heat shield both sides etc.
Seems a lot stronger than the liquid steel JB weld. Anyway I have no welder so I tried this.

P1030497.JPG

Keeping the patina I am!

Curtis · Post by **Curtis** » Fri Jun 05, 2015 9:52 am

msampsel wrote:I spent the last several days applying JB weld epoxy to my carb heat shield both sides etc.
Seems a lot stronger than the liquid steel JB weld. Anyway I have no welder so I tried this.
P1030497.JPG
Keeping the patina I am!

And the while I am at it is growing to epic proportions!

Nissanman · Post by **Nissanman** » Fri Jun 05, 2015 7:55 pm

Good luck with that heat shield repair.
It is vibration that causes the cracking and methinks it still will

I was able to weld a re-enforcing washer at all the mount holes in the hope that would strengthen the shield from stress cracking.
A slight design flaw on Nissan's part

mraitch · Post by **mraitch** » Fri Jun 05, 2015 8:27 pm

@ msampsel
yoda go you

msampsel · Post by **msampsel** » Fri Jun 05, 2015 11:07 pm

@ mraitch
Teach me you will

pebbles · Post by **pebbles** » Fri Jun 05, 2015 11:36 pm

msampsel wrote:I spent the last several days applying JB weld epoxy to my carb heat shield both sides etc.
Seems a lot stronger than the liquid steel JB weld. Anyway I have no welder so I tried this.
P1030497.JPG
Keeping the patina I am!

shoudnt this be in the "sin poll"?

seriously I have no ides what that fastens too. but me thinks Nissanman is onto something here. add a reinforcing layer of metal to both sides with the JB about .090" thick. overlapp the crack with metal about .500".

we will then poll 5 years.

msampsel · Post by **msampsel** » Sat Jun 06, 2015 5:59 am

pebbles wrote:
msampsel wrote:I spent the last several days applying JB weld epoxy to my carb heat shield both sides etc.
Seems a lot stronger than the liquid steel JB weld. Anyway I have no welder so I tried this.
P1030497.JPG
Keeping the patina I am!

shoudnt this be in the "sin poll"?

seriously I have no ides what that fastens too. but me thinks Nissanman is onto something here. add a reinforcing layer of metal to both sides with the JB about .090" thick. overlapp the crack with metal about .500".

we will then poll 5 years.

I like it, and suspect Nissanman is as usual absolutely correct. Perhaps metal sutures at 90 degrees to my mini San Andreas might be appropriate. Still do not like my chances in a poll against Nissanman! And pebbles good suggestion, do you think
0.500000555 is close enough?

Nissanman · Post by **Nissanman** » Sat Jun 06, 2015 6:55 am

Alternatively, you could use a pair of thin rubber washers either side of the shield to dampen the vibrations.
They should handle the heat OK

msampsel · Post by **msampsel** » Sat Jun 06, 2015 9:03 am

Nissanman wrote:Alternatively, you could use a pair of thin rubber washers either side of the shield to dampen the vibrations.
They should handle the heat OK

Brilliant

! I'll find some o-rings or washers today, thanks for the tip.

pebbles · Post by **pebbles** » Sat Jun 06, 2015 4:01 pm

msampsel wrote: 0.500000555 is close enough?

Miles? No
Inches? Yes.

Alvin · Post by **Alvin** » Sat Jun 06, 2015 9:43 pm

I replaced my window squeegees today. It's been on my list for years and I finally bought a set along with the wing/frame squeegee from Dean.

My old window squeegees were torn and probably deteriorated from my sweaty arm hanging out over the years:

Dean's squeegees are great and I love the way they look:

Wing window rubbers:

Datsun Roadster Forum-311s.org

What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)

Re: What did you do TO or FOR your Datsun today?(Roadsters only)