more Hayashis

Garm · Post by **Garm** » Fri Feb 24, 2012 11:29 am

I know, I'm terrible.
Picked these up last night. Yeah, five of them. Hayashi Talons

Fitment is going to be a challenge, as they are 15x7.
We'll see how it goes -- stay tuned...

jamesw · Post by **jamesw** » Fri Feb 24, 2012 11:45 am

15 x 7 will fit if the offset is correct. Hope you got +10 or greater - if so you can make 15 x 7's work.

fj20spl311 · Post by **fj20spl311** » Fri Feb 24, 2012 11:50 am

Garm wrote: Picked these up last night. Yeah, five of them. Hayashi Talons

Get about 5 more sets and we might start calling you.......VICTOR

Garm · Post by **Garm** » Fri Feb 24, 2012 2:46 pm

I'll answer to that.

Alvin · Post by **Alvin** » Sat Feb 25, 2012 11:44 pm

for some reason they remind me of C4 'vette wheels..or ronal turbos

68DSU · Post by **68DSU** » Tue Feb 28, 2012 6:42 pm

Garm wrote:Fitment is going to be a challenge, as they are 15x7.
We'll see how it goes -- stay tuned...

Looks to me like all you need is a really, really big phillips screwdriver.

pebbles · Post by **pebbles** » Tue Feb 28, 2012 8:24 pm

And hope that at least two are left hand thread!

Alvin · Post by **Alvin** » Wed Feb 29, 2012 12:29 am

68DSU wrote:
Garm wrote:

Looks to me like all you need is a really, really big phillips screwdriver.

OMG that was too funny!
I hope your are here the rest of the week...

Post by **dbrick** » Wed Feb 29, 2012 1:39 am

Alvin wrote:
68DSU wrote:
Garm wrote:

Looks to me like all you need is a really, really big phillips screwdriver.
OMG that was too funny!
I hope your are here the rest of the week...

It's tough to thread the hubs and axles...
Tip your waiters, Try the Veal

Garm · Post by **Garm** » Thu Mar 01, 2012 12:04 am

LOL, now I can't look at them and NOT think of that.

Post by **dbrick** » Fri Mar 02, 2012 12:56 am

Garm wrote:LOL, now I can't look at them and NOT think of that.

Our work is done here

nismou20 · Post by **nismou20** » Fri Mar 02, 2012 4:15 pm

I'm kinda likin the new Enkei Apache 2 kinda retro 4 spokey but they are 15x7 +38. Would these fit our cars?

Alvin · Post by **Alvin** » Fri Mar 02, 2012 11:32 pm

nismou20 wrote:I'm kinda likin the new Enkei Apache 2 kinda retro 4 spokey but they are 15x7 +38. Would these fit our cars?

kick them out with 20mm spacers and it should work

Garm · Post by **Garm** » Mon Mar 05, 2012 2:37 pm

They arrived.

Super deep lip looks awesome.

Rear openings don't quite fit the hub, will require a little "porting" in the back of the wheel. So I couldn't quite bolt one on. Extended studs will be needed too.

They are super aggressive with a little poke at least on the front (the one I tried). I'm going to sit with them for a few days and decide whether to keep them or not. I like the ones on the car better at the moment.

fj20spl311 · Post by **fj20spl311** » Mon Mar 05, 2012 3:02 pm

A piloted router is the best tool for porting the concentric hub hole.
Phil

Datsun Roadster Forum-311s.org

more Hayashis

more Hayashis

Re: more Hayashis

Re: more Hayashis

Re: more Hayashis

Re: more Hayashis

Re: more Hayashis

Re: more Hayashis

Re: more Hayashis

Re: more Hayashis

Re: more Hayashis

Re: more Hayashis

Re: more Hayashis

Re: more Hayashis

Re: more Hayashis

Re: more Hayashis