Hi All,
I have a '68 1600 which has been upgraded to LED 1157 blubs and EF32RLNP flasher cans.
With the lights off the flashers work a treat.
With the headlights on one of my flashers (rear passenger side) fails to work, either with the turn signal or with the hazards. The light stays on solid.
Any ideas?
Flasher & Light Combo Issue
Moderators: notoptoy, S Allen, Solex68
-
- Roadster Newby
- Posts: 9
- Joined: Wed Sep 04, 2019 4:50 pm
- Location: Houston, TX
- Model: 1500/1600
- Year: High Windshield-68-70
- Linda
- Fraternal Den Mother-RIP
- Posts: 7807
- Joined: Sat Nov 05, 2005 11:37 pm
- Location: Los Angeles
- Model: 1500/1600
- Year: High Windshield-68-70
Re: Flasher & Light Combo Issue
The cans have to be mounted to clean bare metal where they screw in to the car, for a good ground.
Linda
Linda
Sadly-Linda has passed away 2022. She was the 311's den mother and drove the first Rare-Parts ball joint project. RIP.
-
- Roadster Newby
- Posts: 9
- Joined: Wed Sep 04, 2019 4:50 pm
- Location: Houston, TX
- Model: 1500/1600
- Year: High Windshield-68-70
Re: Flasher & Light Combo Issue
Thanks Linda. Looks like the cans are grounded to an aftermarket bracket in the foot well which seem to have some resistance. I will run a wire to a known good ground and see if it fixed the problem. I just hope I don't have an issue in the loom somewhere!
-
- Roadster Newby
- Posts: 9
- Joined: Wed Sep 04, 2019 4:50 pm
- Location: Houston, TX
- Model: 1500/1600
- Year: High Windshield-68-70
Re: Flasher & Light Combo Issue
No luck. Cans are well grounded. Very strange issue.
- redroadster
- Roadsteraholic
- Posts: 2402
- Joined: Tue Mar 12, 2013 10:58 am
- Location: KCMO
- Model: 1500/1600
- Year: High Windshield-68-70
Re: Flasher & Light Combo Issue
The flashers are rated for the low amp led bulbs ?
the older 60s circuit breaker flasher blow / open circuits because the bulbs draw more amps than the circuit can take then resets to do it again... later they have a timer that gives conn.
A weak conn. Does / causes the same thing
I would run a power pos wire directly to the Tc swt see if it fixes if not , directly to the flasher. That should make it flash
If not you have a problem flasher to bulbs
You could have a feed back problem
the older 60s circuit breaker flasher blow / open circuits because the bulbs draw more amps than the circuit can take then resets to do it again... later they have a timer that gives conn.
A weak conn. Does / causes the same thing
I would run a power pos wire directly to the Tc swt see if it fixes if not , directly to the flasher. That should make it flash
If not you have a problem flasher to bulbs
You could have a feed back problem
Datsun dealer tech 76 to 87
Mitsubishi tech 9 yrs
Volvo, Kia, Toyota too
6 month - Rolls Royce
ASE MASTER TECH 96. - 11
70 SPL 86 Z31 T , Sportster
Mitsubishi tech 9 yrs
Volvo, Kia, Toyota too
6 month - Rolls Royce
ASE MASTER TECH 96. - 11
70 SPL 86 Z31 T , Sportster
-
- Roadster Newby
- Posts: 9
- Joined: Wed Sep 04, 2019 4:50 pm
- Location: Houston, TX
- Model: 1500/1600
- Year: High Windshield-68-70
Re: Flasher & Light Combo Issue
Problem fixed...on closer inspection the ground connection on the light housing was loose. I soldered it up and now it works. I also cleaned up all the original bullet connections.
I appreciate the advise!
I appreciate the advise!