gaskets for this job to replace
Moderators: notoptoy, S Allen, Solex68
- Lorna c
- Site Supporter
- Posts: 2428
- Joined: Sat Aug 20, 2016 12:47 am
- Location: central coast , ,ca
gaskets for this job to replace
ok so I've pulled my intake and carbs , headers tomorrow . anyway . it looks like I'm going to need a few gaskets here . looks like everything is blown . haha weehaa
so can anyone tell me which gaskets to get please .. I know the intake one I'll need but I didn't put the carbs onto the intake and don't know what's needed to tighten things up ... please help ... I need to order them today /tomorrow .. hopefully this is all I'll be pulling . oh and looks like my frankenheader might be ok after all . all the gaskets around it are blown crateing all the soot I think..
so can anyone tell me which gaskets to get please .. I know the intake one I'll need but I didn't put the carbs onto the intake and don't know what's needed to tighten things up ... please help ... I need to order them today /tomorrow .. hopefully this is all I'll be pulling . oh and looks like my frankenheader might be ok after all . all the gaskets around it are blown crateing all the soot I think..
You do not have the required permissions to view the files attached to this post.
"Is it me, or does everyone want to race ?"
late 68 1600 3 main motor .
- Lorna c
- Site Supporter
- Posts: 2428
- Joined: Sat Aug 20, 2016 12:47 am
- Location: central coast , ,ca
Re: gaskets for this job to replace
here's some other pics
You do not have the required permissions to view the files attached to this post.
"Is it me, or does everyone want to race ?"
late 68 1600 3 main motor .
- fj20spl311
- Roadsteraholic
- Posts: 5009
- Joined: Mon Nov 28, 2005 3:54 pm
- Location: San Diego, Ca
Re: gaskets for this job to replace
REMFLEX makes a thick gasket for the R motor.
http://catalog.remflex.com/DATSUN_1600_ ... 15-010.htm
Available from Summit
https://www.summitracing.com/search?Sor ... x%2015-010
http://catalog.remflex.com/DATSUN_1600_ ... 15-010.htm
Available from Summit
https://www.summitracing.com/search?Sor ... x%2015-010
Phil
67.5 SRL311-00148 Blue (FJ cruiser VOODOO Blue)
67.5 SPL311 FJ20E teal SDS EFI
69 SRL311 SOLD
19 Raptor SCAB
67.5 SRL311-00148 Blue (FJ cruiser VOODOO Blue)
67.5 SPL311 FJ20E teal SDS EFI
69 SRL311 SOLD
19 Raptor SCAB
- Lorna c
- Site Supporter
- Posts: 2428
- Joined: Sat Aug 20, 2016 12:47 am
- Location: central coast , ,ca
Re: gaskets for this job to replace
thank you . this helps
"Is it me, or does everyone want to race ?"
late 68 1600 3 main motor .
- Lorna c
- Site Supporter
- Posts: 2428
- Joined: Sat Aug 20, 2016 12:47 am
- Location: central coast , ,ca
Re: gaskets for this job to replace
can you do that for other gaskets ? there's some things metal to metal still .like, distributor , fuel pump , and the top of the block where the water fill thermostat thing ,fj20spl311 wrote: ↑Mon Jun 04, 2018 9:47 pm REMFLEX makes a thick gasket for the R motor.
http://catalog.remflex.com/DATSUN_1600_ ... 15-010.htm
Available from Summit
https://www.summitracing.com/search?Sor ... x%2015-010
next to valves , oops need valves cover one too . but the thermostat housing next to valves . I need too . it looks like that guy I got intake header gasket from , I didn't see any others in this car ??
"Is it me, or does everyone want to race ?"
late 68 1600 3 main motor .
- fj20spl311
- Roadsteraholic
- Posts: 5009
- Joined: Mon Nov 28, 2005 3:54 pm
- Location: San Diego, Ca
Re: gaskets for this job to replace
Others should be able to help. I have been running FJ20 engines for the past decade or two and don't have any current information.
My newest car has a U20, so I am starting to gather information.
My newest car has a U20, so I am starting to gather information.
Phil
67.5 SRL311-00148 Blue (FJ cruiser VOODOO Blue)
67.5 SPL311 FJ20E teal SDS EFI
69 SRL311 SOLD
19 Raptor SCAB
67.5 SRL311-00148 Blue (FJ cruiser VOODOO Blue)
67.5 SPL311 FJ20E teal SDS EFI
69 SRL311 SOLD
19 Raptor SCAB
- boxcar
- Roadster Nut
- Posts: 70
- Joined: Thu Mar 15, 2018 12:56 pm
- Location: Astoria oregon USA
Re: gaskets for this job to replace
Ralley enterprises has, what I believe to be, the best selection of gaskets for your engine. a complete rebuild set with header gasket is $262.
part # 101-02H
You may want to go that rout rather than trying to peace together what you think you might need. With a full kit you will know you have all of the gaskets you need.
part # 101-02H
You may want to go that rout rather than trying to peace together what you think you might need. With a full kit you will know you have all of the gaskets you need.
- Lorna c
- Site Supporter
- Posts: 2428
- Joined: Sat Aug 20, 2016 12:47 am
- Location: central coast , ,ca
Re: gaskets for this job to replace
thanks . I was looking on there last night ... good luck in ur new er car
"Is it me, or does everyone want to race ?"
late 68 1600 3 main motor .
- Lorna c
- Site Supporter
- Posts: 2428
- Joined: Sat Aug 20, 2016 12:47 am
- Location: central coast , ,ca
Re: gaskets for this job to replace
these look the same to me ... can anyone show me what a better gasket for my car would be please for a header.?
You do not have the required permissions to view the files attached to this post.
"Is it me, or does everyone want to race ?"
late 68 1600 3 main motor .
- mraitch
- Roadsteraholic
- Posts: 3629
- Joined: Mon Oct 02, 2006 7:03 pm
- Location: Lake Balboa (SFV) - CA
- Model: 1500/1600
- Year: High Windshield-68-70
- Contact:
Re: gaskets for this job to replace
lorna
exactly what are you intending to replace?
head gasket?
manifold (header/intake gasket) ?
head gasket is pretty intolerant of any deviations from FLAT
manifold, not same pressure, more tolerant, but you should be able to torque down - starting from inside with no problem, or use copper gasket additive - though difficult to remove
exactly what are you intending to replace?
head gasket?
manifold (header/intake gasket) ?
head gasket is pretty intolerant of any deviations from FLAT
manifold, not same pressure, more tolerant, but you should be able to torque down - starting from inside with no problem, or use copper gasket additive - though difficult to remove
Peter Harrison
1970 1600 (Stroker) - TOAD SAN (Eliza)
1970 1600 (Stock) - As Yet Unnamed
Lake Balboa (SFV) , California
1970 1600 (Stroker) - TOAD SAN (Eliza)
1970 1600 (Stock) - As Yet Unnamed
Lake Balboa (SFV) , California
- Lorna c
- Site Supporter
- Posts: 2428
- Joined: Sat Aug 20, 2016 12:47 am
- Location: central coast , ,ca
Re: gaskets for this job to replace
no not head gasket , the one for the header/intake spot . the one I have is holding fine , but told it may blow because it's one for a manifold not header or something like that. just to have one on hand ... I can't tell the difference between them.. but this one may hold , but may not .. it's a gooood gasket too so I hope it holds .. I'm only trying to learn ..mraitch wrote: ↑Tue Jun 12, 2018 10:58 pm lorna
exactly what are you intending to replace?
head gasket?
manifold (header/intake gasket) ?
head gasket is pretty intolerant of any deviations from FLAT
manifold, not same pressure, more tolerant, but you should be able to torque down - starting from inside with no problem, or use copper gasket additive - though difficult to remove
"Is it me, or does everyone want to race ?"
late 68 1600 3 main motor .
- Linda
- Fraternal Den Mother-RIP
- Posts: 7807
- Joined: Sat Nov 05, 2005 11:37 pm
- Location: Los Angeles
- Model: 1500/1600
- Year: High Windshield-68-70
Re: gaskets for this job to replace
Lorna ,
Look at the Remflex gasket pic you posted.
Now look at the pic for gasket part 1287
on datsunparts.com site.
Keep staring at the pics til you can see the difference. It's there.
Linda
Look at the Remflex gasket pic you posted.
Now look at the pic for gasket part 1287
on datsunparts.com site.
Keep staring at the pics til you can see the difference. It's there.
Linda
Sadly-Linda has passed away 2022. She was the 311's den mother and drove the first Rare-Parts ball joint project. RIP.
- Lorna c
- Site Supporter
- Posts: 2428
- Joined: Sat Aug 20, 2016 12:47 am
- Location: central coast , ,ca
Re: gaskets for this job to replace
ok I will .
"Is it me, or does everyone want to race ?"
late 68 1600 3 main motor .
- Lorna c
- Site Supporter
- Posts: 2428
- Joined: Sat Aug 20, 2016 12:47 am
- Location: central coast , ,ca
Re: gaskets for this job to replace
well that's easy to see now .. thanks !
You do not have the required permissions to view the files attached to this post.
"Is it me, or does everyone want to race ?"
late 68 1600 3 main motor .
- Lorna c
- Site Supporter
- Posts: 2428
- Joined: Sat Aug 20, 2016 12:47 am
- Location: central coast , ,ca
Re: gaskets for this job to replace
and girth aroy each hole
"Is it me, or does everyone want to race ?"
late 68 1600 3 main motor .